Glass Industry News

Clean heating and cooling - Siemens PLM Software facilitates energy-saving heat pump development

, Siemens AG

Clean heating and cooling - Siemens PLM Software facilitates energy-saving heat pump development

ThermoLift has developed the ThermoLift system at its headquarters in the Advanced Energy Center at the State University of New York, (SUNY). This device, which is driven by natural gas, combines air conditioning system and heat pump in a single unit. ThermoLift chose Siemens PLM Software solutions for the development and automated design optimization processes, as well as for simulating the design process. A very high number of components can be included in the simulation and multi-disciplinary simulations can be achieved in a single user interface by using Simcenter Star CCM +. The optimum design of the ThermoLift solution allows the energy costs for the heating, cooling and hot water systems in a building to be reduced by 30 to 50 percent compared to conventional systems.

 

ThermoLift has developed the ThermoLift system which combines air conditioning system and heating pump in a single unit which is driven by natural gas.

 

Most people in the USA use ovens or boilers to keep their houses and apartments warm. Only a small number use heat pumps which heat the buildings using environmental heat. These units are often electrically driven and this is the starting point for the founders of ThermoLift, Dr. Peter Hofbauer und Paul Schwartz. Their ThermoLift system for a modern heating, ventilation, and air conditioning (HVAC) system is similar to a standard Vuilleumier heat pump but uses a special temperature cycle (the TC cycle). In order to improve the simulation-led design process, ThermoLift has been working for a few years with the Simcenter simulation software from the Siemens PLM Software portfolio.

Precise simulation of extremely complex physics
A conventional Vuilleumier heat pump moves a gas such as helium between three chambers in a closed system. Two so-called displacers slide back and forth inside a cylinder. The expansion or compression of the gas occurs due to the cold or hot thermodynamic cycle. The particular feature of the ThermoLift device compared to a Vuilleumier heat pump is that the displacers are controlled separately from the mechatronics in order to provide better control of the displacer movement, and therefore the thermodynamic cycle. The whole ThermoLift system consists of several modules such as the heat exchanger, regenerators and displacers which are produced during the design process. ThermoLift chose Simcenter Star CCM + for the simulation and modelling of the complex physics involved. The software is a comprehensive solution which allows multi-disciplinary simulation in a single user interface. In addition to this, Star CCM + allows more components to be integrated into the simulation which speeds up the design process and produces even more accurate results.

Economical and reliable
The ThermoLift system's optimized design process means that the energy losses can be reduced significantly compared to conventional Vuilleumier heat pumps. This leads to energy cost savings of 30 to 50 percent. The displacers' 'soft landing' also reduces machine noise while achieving operating times of over ten hours.

, © Siemens AG

News material on the Site is copyright and belongs to the Company or to its third party news provider, and all rights are reserved. Any User who accesses such material may do so only for its own personal use, and the use of such material is at the sole risk of the User. Redistribution or other commercial exploitation of such news material is expressly prohibited. Where such news material is provided by a third party, each User agrees to observe and be bound by the specific terms of use applying to such news material. We do not represent or endorse the accuracy or reliability of any of the info contained in any news or external websites referred to in the news.

Should the content or the design of these sites violate third parties rights or legal prescriptions, we kindly ask you to send us a respective message without invoice or cost. We guarantee that passages where the claim is considered as justified will be removed immediately, without any necessity to involve any lawyer into this issue. We will reject any claim caused by submission of a honorary note in this regard without any prior contact and confirmation of the issueby us and we reserve the right ssue counter claim ourselves because of violation of aforesaid conditions.



Info Grid

Glass studies

Updated worldwide glass study 2024

plants.glassglobal.com

Updated hollow glass study 2024

Request more information

Updated float glass study 2024

Request more information

Further glass market studies

Request more information

Company Profile



Updated worldwide glass market study 2024 available now for flat, container glass and tableware

We have updated our international studies on flat glass, container glass and tableware for 2024.

This unique software provides a global overview about glass producers and technical details. Easy to use and clear tables summarize information and data about glass makers such as: Glass types: flat glass, container glass, tableware, production capacities in regions and countries, number of furnaces, furnace types, year of construction, glass types and sub-types, products, project information, special news and downloads.

Further databases supplying demoscopic data and import and export data complete the market survey. Based on these data, prepare individual country profiles with information about local production capacities, local market sizes and expected demand in the future.

Request your offer via plants.glassglobal.com.

Updated container glass study 2024

X

Updated float glass study 2024

X

Further glass studies and reports 2024

X