Glass Industry News

IS machine innovation delivers greater daily output – Glass Worldwide

, T&T

An acronym for eXtra large IS machine, the ISX is described by Rolf Themann as a beast, with twice the cooling capacity of any other IS machine in the market. It can cope, for example, with up to 220 tons/day on a single 12-section IS machine in triple gob configuration for wine production or quad gob for beer or energy drinks. Potentially, this means a daily output of approximately 620,000 0.75 litre wine bottles or 1.1 million 0.33 litre beer bottles every day.

T&T Turnov sro recently unveiled the so-called ISX machine. It can produce very large bottles of up to 1.5 litre wine or spirits in triple gob with a centre distance of two x 6 ¼in (12½ triple). But the machine has to offer much more. Besides the triple gob version, the machine can be changed and upgraded to quad gob with a centre distance of three x 4 ¼in (12 ¾ quad).

Or on the other hand, there are also smaller versions of double/triple gob combinations, for example 6 ¼in double gob with 4 ¼in triple gob. The same machine platform is used for all centre distances. This makes for a highly flexible machine. Thus, the production of any still or sparkling wine and Champagne bottles or large liqueur bottles with triple gob finally becomes possible as standard, whereas in quad gob configuration, mass markets such as beer, energy drinks and baby food jars can be produced. The machine uses latest state-of-the-art servo technology components.

It features a 50% lower energy consumption than conventional IS machines, while ISX sections can be easily and quickly exchanged and replaced in the case of job changes, section damage or exchange. Section exchange takes no more than 20 minutes to complete. To do so, T&T also offers a vehicle to easily remove and insert the entire section. The only precondition is that the ISX machine is installed into the ground in order to have full access, with no height barriers in between the sections and the operator.

Benefits and features
Features of the ISM machine include the following:

  • Servo-electric mechanisms provide precise, repeatable motion.
  • Allows for 6 ¼in triple gob production runs at the same speed as double gob.
  •  Allows for 4 ¼in quad gob production runs at the same speed as triple gob.
  •  User-friendly and ergonomic design.
  •  Energy consumption reduced by 50%.
  •  Quick change sections.
  •  Handles all moulds and sizes, old and new alike. Because glass plants invest heavily in their moulds, this is very important.
  •  Highly accurate control system, controlled via the use of 100% Siemens standard components.
  •  Production sizes featuring the widest range of ware sizes, from heights of 15mm to 400mm.
  •  Section-related controls for service independence.
  •  Capable of using all cooling processes: Axial 360° on BB, Vertiflow and InVertiflow on the blank and blow mould sides.
  •  Each mould half and mould A, B, C, D plus neckrings can be cooled individually. The specifications for the ISX machine and ware ranges are given in table 1.

, © T&T

News material on the Site is copyright and belongs to the Company or to its third party news provider, and all rights are reserved. Any User who accesses such material may do so only for its own personal use, and the use of such material is at the sole risk of the User. Redistribution or other commercial exploitation of such news material is expressly prohibited. Where such news material is provided by a third party, each User agrees to observe and be bound by the specific terms of use applying to such news material. We do not represent or endorse the accuracy or reliability of any of the info contained in any news or external websites referred to in the news.

Should the content or the design of these sites violate third parties rights or legal prescriptions, we kindly ask you to send us a respective message without invoice or cost. We guarantee that passages where the claim is considered as justified will be removed immediately, without any necessity to involve any lawyer into this issue. We will reject any claim caused by submission of a honorary note in this regard without any prior contact and confirmation of the issueby us and we reserve the right ssue counter claim ourselves because of violation of aforesaid conditions.



Info Grid

Glass studies

Updated worldwide glass study 2024

plants.glassglobal.com

Updated hollow glass study 2024

Request more information

Updated float glass study 2024

Request more information

Further glass market studies

Request more information

Company Profile



Updated worldwide glass market study 2024 available now for flat, container glass and tableware

We have updated our international studies on flat glass, container glass and tableware for 2024.

This unique software provides a global overview about glass producers and technical details. Easy to use and clear tables summarize information and data about glass makers such as: Glass types: flat glass, container glass, tableware, production capacities in regions and countries, number of furnaces, furnace types, year of construction, glass types and sub-types, products, project information, special news and downloads.

Further databases supplying demoscopic data and import and export data complete the market survey. Based on these data, prepare individual country profiles with information about local production capacities, local market sizes and expected demand in the future.

Request your offer via plants.glassglobal.com.

Updated container glass study 2024

X

Updated float glass study 2024

X

Further glass studies and reports 2024

X